7 Push Pull Pot Mods For Guitar & More

Guitar mods with a push-pull pot can revolutionize your sound, offering a spectrum of tonal possibilities with a simple tug or push. This nifty device transforms your guitar, allowing you to switch from the lush humbucker warmth to the crisp bite of a single coil without swapping guitars.

Beyond coil splitting, push-pull pots open the door to an array of sonic tweaks. Phase reversal for vintage vibes, kill switches for rhythmic flair, or expanded pickup combinations—all lie within reach, enhancing your musical canvas while maintaining the guitar's original character.

Understanding Push-Pull Pots

The Basics of Push-Pull Pots

A push-pull pot combines a standard control potentiometer and a DPDT switch, allowing for complex wiring guitar mods in a compact form. By pulling or pushing the potentiometer's knob, you engage or disengage the switch, respectively. This ability to switch can expand your guitar's tonal options dramatically.

How Push-Pull Pots Work

Each push-pull pot consists of two main components:

1. The potentiometer: This adjusts your guitar's volume or tone.
2. The DPDT switch: This is what changes the wiring circuit when you push or pull the knob.

The switch has six contacts, called lugs, which you can use to reroute the signal path in your guitar's circuit. By connecting wires to these lugs, you can add functionality like coil splitting, series/parallel pickup switching, or activating pickups that are usually not together in standard wiring.

Blower Switch

A Blower Switch is an effective mod for your guitar, providing swift access to a direct signal from your pickup to the output jack. Typically, this bypasses the tone and volume controls, affording you the clearest possible signal without any attenuation.

Installation:

• Integrate a DPDT (double-pole, double-throw) switch into your guitar circuit.
• Wire the switch to connect your pickup directly to the output jack when engaged.

Operation:

• Engage the blower switch to bypass the guitar's volume and tone controls.
• Disengage to return to the standard control setup.

Here's a simple step-by-step process:

1. Choose a suitable location on your guitar for the blower switch.
2. Drill a hole (if necessary) and carefully install the DPDT switch.
3. Solder the pickup's hot wire to one pole of the switch.
4. Connect the switch's second pole to the output jack.

Benefits:

• Achieve maximum signal clarity and volume instantaneously.
• Easily return to your usual tone setup with a flip of the switch.

Considerations:

• Ensure your guitar has enough space for the additional switch.
• Be prepared for a stronger signal that may drive your amp harder when engaged.

Bright/Mud Switch

When you modify your guitar with a push-pull pot, one popular mod you can implement is the Bright Switch. This modification increases the treble and clarity of your sound, ideal for cutting through a mix. By activating the switch, you bypass certain signal route components, such as the volume and tone pots, leading to a brighter tone.

Here’s how it influences your guitar’s sound:

• Engaged: Your signal path is more direct, which emphasizes higher frequencies.
• Disengaged: You retain the normal operation and tonal characteristics of your guitar.

Conversely, a Mud Switch mod does quite the opposite. It introduces a capacitor into the signal path when engaged, which reduces high frequencies, resulting in a warmer and darker tone. This mode is perfect when you need a thicker sound that doesn't pierce as sharply.

Your wiring may vary, but here's a basic idea to get you started:

• Pull: Triggers the addition of the capacitor, initiating the "Mud" mode.
• Push: Returns the pot to its standard operation, deactivating the mod.

Remember to choose a capacitor value that matches the tonal change you desire; smaller values for subtle darkness, larger for more pronounced effect. Be sure to work with a push-pull pot that corresponds with your pickups' output level, generally using 250K or 500K pots, depending on whether they are single-coil or humbuckers.

Coil Splitting

When you're looking to add versatility to your guitar's tone, coil splitting is a highly effective modification. This technique allows you to switch between a full humbucker sound and the crisper tone of a single coil.

A push-pull pot is often used to achieve coil splitting and is incorporated into your guitar's existing volume or tone control. By pulling the knob out, you activate the split, sending one coil of the humbucker to ground and essentially "turning off" that coil. This leaves one active coil, mimicking the sound of a single coil pickup.

For successful coil splitting, your humbucker must have 4-conductor wiring, which provides access to each coil independently. If you're uncertain about your pickup's compatibility, consulting a wiring diagram or a professional can clarify whether your pickup supports this mod.

Wiring Steps:

• Identify and separate the 4-conductor wires.
• Connect the pickup coils' series link to the pot.
• Link the pot's switch to ground, activating the split when pulled.

Kill Switch

Components Required:

• 2PDT Push-pull Pot: This will replace one of your existing pots and includes an integrated switch that will serve as the kill switch.
• Soldering Tools: To connect the components securely.

Installation Steps:

1. Remove the original pot from your guitar.
2. Solder the input and output from the guitar's jack to the respective lugs on the pot.
3. Connect a ground wire to one side of the switch and connect that to the guitar's common ground.
4. Mount the push-pull pot back to the guitar.

When you pull the knob, the switch disengages the guitar's output by interrupting the signal path and grounding it out, effectively "killing" the sound. Pushing the knob back down will restore normal functionality.

If you want a faster action of this switch, you can try something that's spring-loaded like the Iron Age switches we carry here. These momentary switches allow you to activate much faster and add a rhythmnic element to your playing. Learn more about guitar kill switches.

Related: Different Types of Kill Switches

Phase Reverse

When considering modifications for your guitar, the phase reverse using a push-pull pot is a particularly interesting option that can dramatically alter your tone. By reversing the phase of one of your pickups, you create a unique sound with a potentially nasal and hollow characteristic.

Here's what happens:

• In normal operation, your guitar pickups work in phase, meaning their signals combine constructively.
• Engaging a phase reverse causes one pickup to work against the other, resulting in a cancellation effect where certain frequencies are reduced, creating that distinct sound.

To implement a phase reverse mod:

1. Decide which pickup you want to phase reverse – typically the neck or bridge.
2. Replace the standard tone pot with a push-pull pot.
3. Wire the phase-reverse switch so that pulling the pot reverses the polarity of the selected pickup.

This modification is not only effective but also non-intrusive, as it doesn't require additional drilling or permanent changes to your guitar. It can offer a whole new palette of sounds, which is particularly useful in creating contrast or cutting through a mix in certain musical situations.

For visual guidance on wiring this modification, ensure to check out the detailed instructions on phase reverse with blender pot modification. This reference includes a schematic and a step-by-step approach to performing the mod effectively.

Series and Parallel Wiring

When you use a push-pull pot with your guitar, you gain the ability to switch between series and parallel wiring modes for your pickups. Understanding how each mode affects your sound is crucial for tailoring your guitar's tone.

Series Wiring: In series wiring, the pickup coils are connected end-to-end, creating one long path for the signal. This results in a:

• Fuller and louder sound
• Increased midrange and overall output
• Characteristics ideal for heavy and rich tones

To achieve series wiring, your humbucker needs to have four accessible leads.

Parallel Wiring: Alternatively, parallel wiring connects the coils in your humbucker side by side. With this setup, the signal can travel through both coils simultaneously, which generally produces:

• A brighter, crisper tone
• A sound with less output than series
• A clear texture often preferred for clean channels

Switching Between Modes:

Experiment with a push-pull pot to find which mode works best for your style. These modifications may require some basic soldering and understanding of your guitar's electronics.

Seven-sound Strat

When you modify your Stratocaster with a push-pull pot, you unlock a spectrum of tonal possibilities. Famed for its five distinct tones, the Strat can be transformed into a seven-sound wonder with this clever addition.

First, the basics: your Strat's five-way switch already provides a range of tones by selecting between the three pickups. Typically, you can combine the bridge and middle, or the middle and neck pickups for a total of five sounds.

The seven-sound mod involves wiring the neck pickup to the push-pull pot, enabling you to activate it regardless of the five-way switch's position. Here's what you gain:

• Bridge pickup alone (classic biting Strat tone)
• Middle pickup alone (warmer with less twang)
• Neck pickup alone (rich and mellow)
• Bridge and middle together (combines bite with warmth)
• Middle and neck together (velvety tones ideal for rhythm)
• Bridge and neck together (not standard on a Strat without mod)
• All three pickups together (adds depth to the overall sound)

To implement this mod, it's essential you're comfortable with basic soldering and wiring techniques. The modification doesn't change the exterior look of your guitar but brings a fresh landscape of sounds for you to explore. For a visual guide and further technical details, Sweetwater provides a thorough explanation of mods that include the seven-sound Strat modification.

Remember, modifications like these can void your warranty, so take this into account before proceeding, and consider consulting with a professional if you're unsure about tackling the job yourself.

Crafting Your Sound

Selecting the Right Components

The journey to your unique sound starts with selecting the right components. For the push-pull mechanism, the choice between a 250k and 500k tone pot can influence the overall warmth or brightness of your sound. Thoroughly research your guitar's original specifications—some, like Fender, typically use 250k pots, while Gibsons often come with 500k. This isn't just about personal preference but about matching the component to your guitar's inherent qualities.

Push-pull pots are versatile, allowing for innovative configurations like the Seven-sound Strat mod, which enables the activation of all pickups simultaneously, or the Phase Reverse with Blender Pot Modification, providing nuanced tonal changes unachievable with standard setups.

The Impact of Tone Caps on Sound

When considering tone caps, it's crucial to know that their values (measured in microfarads, µF) affect your guitar's tone. Lower values, like .022µF, keep the sound bright, while higher values, such as .047µF, yield a warmer tone. It's essential to pair the cap value well with your chosen pickups, as this determines the effectiveness of the tone control's sweep and overall clarity. For single-coil pickups, a value on the lower end is common, while humbuckers can benefit from a slightly higher value to temper their natural darkness.

Modifications like the Bright Switch use the push-pull function to bypass the tone cap and pot, sending the signal directly to the output jack for a clearer, unfiltered sound. This adjustment is no small change; it can significantly enhance the crispness of the tone, especially when used in tandem with brighter pickups.

Troubleshooting and Maintenance

Common Issues with Push-Pull Pots

Hum and Noise Issues:

• Loose Connections: Check for loose wiring or solder joints; these can cause intermittent sound and noise.
• Faulty Grounding: Poor grounding can result in a persistent hum. Ensure that the pot is grounded to the guitar's common ground.

Physical Wear:

• Scratchy Sound: If turning the pot results in a scratchy noise, this may indicate dirt or corrosion. A contact cleaner can resolve this.
• Stiff or Sluggish Movement: Lubrication with a suitable potentiometer grease can improve movement.

Electrical Problems:

• Defective Pot: A potentiometer can wear out or become defective. If troubleshooting doesn't resolve the issue, replace the push-pull pot.

Maintaining Your Guitar Mods

Regular Inspection:

• Inspect connections periodically to catch and rectify issues early.
• Ensure wires are well-secured and have no signs of fraying or corrosion.

Clean and Protect:

• Use a soft cloth to clean the potentiometer's knob and shaft, avoiding dust buildup that could enter the casing.
• A scheduled application of contact cleaner helps maintain electrical integrity and prevent scratchy sounds when using the pot.

Also in Iron Age || General Blog